硫氧镁水泥/聚苯乙烯复合材料燃烧性能研究

doi:10.16265/j.cnki.issn1003-3033.2020.06.005

中国安全科学学报 ›› 2020, Vol. 30 ›› Issue (6): 31-36.doi: 10.16265/j.cnki.issn1003-3033.2020.06.005

硫氧镁水泥/聚苯乙烯复合材料燃烧性能研究

于水军^1,2,3 教授, 谢高超¹, 任茉¹, 杨岱霖¹

1.河南理工大学安全科学与工程学院,河南焦作 454003;
2.煤炭安全生产河南省协同创新中心,河南焦作 454003;
3.河南省煤矿瓦斯与火灾防治重点实验室,河南焦作 454003

收稿日期:2020-03-04 修回日期:2020-05-28 出版日期:2020-06-28 发布日期:2021-01-28
作者简介:于水军(1962—),男,河南漯河人,硕士,教授,硕士生导师,主要从事建筑节能新材料和煤矿防灭火新材料安全性能方面的研究。E-mail:yusj0509@126.com。
基金资助:
国家自然科学基金资助(51304069);国家重点研发计划项目(2018YFC0807900);教育部长江学者和创新团队发展计划项目(IRT0618)。

Study on combustion properties of magnesium oxysulfate cement/polystyrene composites

YU Shuijun^1,2,3, XIE Gaochao¹, REN Mo¹, YANG Dailin¹

1. School of Safety Science and Engineering, Henan Polytechnic University, Jiaozuo Henan 454003, China;
2. Coal Production Safety Collaborative Innovation Center in Henan Province, Jiaozuo Henan 454003, China;
3. Henan Province Key Laboratory of Prevention and Control of Gas & Fires, Jiaozuo Henan 454003, China

Received:2020-03-04 Revised:2020-05-28 Online:2020-06-28 Published:2021-01-28

摘要/Abstract

摘要： 针对聚苯乙烯易燃、易产生有毒气体的问题,以硫氧镁水泥、聚苯乙烯颗粒制作硫氧镁水泥/聚苯乙烯复合材料,通过氧指数(LOI)测试试验、UL-94垂直燃烧试验、烟密度测试试验、热重分析(TGA)等试验方法,研究不同配比的轻烧氧化镁和七水硫酸镁对聚苯乙烯颗粒燃烧性能的影响。结果表明:保持硫酸镁含量不变,聚苯乙烯复合材料失重幅度随轻烧氢氧化镁含量增加而降低,失重速率随轻烧氢氧化镁增加而减小;最大质量损失率随轻烧氢氧化镁增加而降低,700 ℃时残炭率随轻烧氢氧化镁含量增加而增大,最大残炭率可达80.73%。硫氧镁水泥包覆的聚苯乙烯颗粒LOI最高可达37.2%,且轻烧氧化镁含量不变,LOI随硫酸镁含量增加而增大;硫酸镁含量不变,LOI随轻烧氧化镁含量增加而增大;硫氧镁水泥包覆聚苯乙烯颗粒的UL-94等级均能达到V-0级别,相比纯聚苯乙烯颗粒烟密度降低约30倍。硫氧镁水泥对聚苯乙烯的阻燃性能和抑烟效果有显著的提高作用。

关键词: 硫氧镁水泥, 聚苯乙烯, 燃烧性能, 氧指数(LOI), UL-94等级, 烟密度, 热重分析(TGA)

Abstract: In order to solve problem that polystyrene is inflammable and easy to produce poisonous gas, magnesium oxysulfate cement and polystyrene particles were used to make magnesium oxysulfate cement/polystyrene composite material. Then, effects of different ratios of lightly-burned magnesium oxide and heptahydrate magnesium oxysulfate on combustion performance of polystyrene particles were studied by LOI test, UL-94 vertical combustion test, smoke density test, and TGA. The results show that when content of magnesium sulfate maintains unchanged, weightlessness range and rate of polystyrene composites decreases with the increase of lightly-burned magnesium oxide, and so does the maximum mass loss rate while residual carbon rate increases with it at 700 ℃ with its maximum rate able to reach 80.73%. LOI of polystyrene coated with magnesium oxysulfate cement can reach up to 37.2%, and it increases along with that of magnesium oxysulfate when lightly-burned magnesium oxide stays fixed. It shows the same trend of LOI increasing along lightly-burned magnesium oxide when the other is unchanged. UL-94 level of composite materials can all reach V-0, and their smoke density is about 30 times lower than that of pure polystyrene particles. Flame retardation and smoke suppression of polystyrene are significantly improved by magnesium oxysulfate cement.

Key words: magnesium oxysulfate cement, polystyrene, combustion performance, limiting oxygen index (LOI), UL-94 level, smoke density, thermogravimtric analysis (TGA)

中图分类号:

X937

于水军, 谢高超, 任茉, 杨岱霖. 硫氧镁水泥/聚苯乙烯复合材料燃烧性能研究[J]. 中国安全科学学报, 2020, 30(6): 31-36.

YU Shuijun, XIE Gaochao, REN Mo, YANG Dailin. Study on combustion properties of magnesium oxysulfate cement/polystyrene composites[J]. China Safety Science Journal, 2020, 30(6): 31-36.

参考文献

[1] KILIARIS P, PAPASPYRIDES C D. Polymer/layered silicate (clay) nanocomposites:an overview of flame retardancy[J].Progress in Polymer Science, 2010, 35(7): 902-958.
[2] YANG F, MANITIU M, KRIEGEL R, et al. Structure, permeability, and rheology of supercritical CO₂ dispersed polystyrene-clay nanocomposites[J]. Polymer, 2014, 55(16): 3 915-3 924.
[3] 张胜, 李玉玲, 谷晓昱,等. 聚苯乙烯泡沫塑料阻燃方法的研究进展[J]. 塑料,2013,42(4): 37-41.
ZHANG Sheng, LI Yuling, GU Xiaoyu, et al. Research progress of flame-retardant PS foams[J]. Plastics, 2013,42(4): 37-41.
[4] 殷海青, 李国珍, 祁正兴,等. 阻燃型氢氧化镁在聚苯乙烯中的应用[J]. 应用化工, 2018,47(6): 1 314-1 316.
YIN Haiqing, LI Guozhen, QI Zhengxing, et al. Application of flame retardant type magnesium hydroxide in polystyrene[J]. Applied Chemical Industry, 2018,47(6): 1 314-1 316.
[5] 于水军, 魏月贝, 杨岱霖,等. 石膏基聚苯乙烯饰面防火板的阻燃性能研究[J]. 中国安全科学学报, 2019,29(1): 31-36.
YU Shuijun, WEI Yuebei, YANG Dailin, et al. Study on flame-retardant properties of gypsum based self-leveling decorative fire-resistant polystyrene board[J]. China Safety Science Journal, 2019,29(1): 31-36.
[6] 于水军, 杨岱霖, 魏月贝,等. 石膏饰面层对聚苯乙烯板耐火性能的影响[J]. 涂料工业, 2019,49(6): 29-34.
YU Shuijun, YANG Dailin, WEI Yuebei, et al. Study on the effect of gypsum finish on the fire resistance of polystyrene board[J]. Paint & Coatings Industry, 2019,49(6): 29-34.
[7] ZHANG Zonglin, HAN Yongqin, LI Tingxi, et al. Polyaniline/montmorillonite nanocomposites as an effective flame retardant and smoke suppressant for polystyrene[J]. Synthetic Metals,2016,221: 28-38.
[8] GB/T8333—2008,硬质泡沫塑料燃烧性能试验方法-垂直燃烧法[S].
GB/T8333-2008, Test method for flammability of rigid cellular plastic-virtical burning method[S].
[9] GB/T2406—2009,塑料-用氧指数法测定燃烧行为[S].
GB/2406-2009, Plastics-determination of burning behaviour by oxygen index[S].
[10] GB/T8627—2007,建筑材料燃烧或分解的烟密度试验方法[S].
GB/T8627-2007, Test method for density of smoke from the burning or decomposition of building materials[S].
[11] 于水军, 陈亮, 魏月贝. 无机包覆聚苯乙烯泡沫板烟气产生规律研究[J]. 安全与环境学报, 2018,18(2): 523-526.
YU Shuijun, CHEN Liang, WEI Yuebei. On the smoke density producing regularity from the inorganic coated polystyrene foam combustion in the fire[J]. Journal of Safety and Environment, 2018,18(2): 523-526.
[12] 白卯娟, 刘岩, 肖凤艳,等. HIPS/OMMT纳米复合材料的燃烧性能与其残余物炭层结构特征研究[J]. 高分子学报, 2012(5): 539-545.
BAI Maojuan, LIU Yan, XIAO Fengyan, et al. Characteristics of fire residues of HIPS/OMMT nanocomposites formed during cone calorimeter tests[J]. Acta Polymerica Sinica, 2012(5): 539-545.

硫氧镁水泥/聚苯乙烯复合材料燃烧性能研究

Study on combustion properties of magnesium oxysulfate cement/polystyrene composites

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

编辑推荐

Metrics

本文评价

[1]	张玉涛, 张玉杰, 李亚清. 凹型结构建筑外立面火灾蔓延特性模拟研究[J]. 中国安全科学学报, 2020, 30(8): 70-78.
[2]	笪良军, 谢启源, 罗圣峰. 倾斜XPS板材向外多向耦合蔓延燃烧特性研究[J]. 中国安全科学学报, 2019, 29(11): 64-70.
[3]	于水军, 魏月贝, 杨岱霖, 谢高超. 石膏基聚苯乙烯饰面防火板的阻燃性能研究[J]. 中国安全科学学报, 2019, 29(1): 31-36.
[4]	卓萍, 倪照鹏, 李向梅, 李强, 闫克勤. 仓储环境对皮棉燃烧性能的影响研究[J]. 中国安全科学学报, 2018, 28(4): 42-46.
[5]	李晓曦, 谭波. 煤自燃阻化剂的阻化效果动力学分析及优选[J]. 中国安全科学学报, 2017, 27(6): 79-84.
[6]	解启航, 张金锋教授, 李艳丽, 郑艳敏, 王浩, 柳晓凯. 7-ACA粉体燃爆机制的热动力学研究^*[J]. 中国安全科学学报, 2017, 27(11): 49-54.
[7]	郝朝瑜，王鑫阳，赵庆彪，王继仁. 低变质程度煤自燃特性的改进着火活化能方法研究[J]. 中国安全科学学报, 2013, 23(10): 27-.
[8]	黄新杰，丁厚成，张浩，张英，孙金华. 海拔对聚苯乙烯火蔓延温度场特性影响的研究[J]. 中国安全科学学报, 2012, 22(10): 36-.
[9]	罗静，樊刚，郑艳琼，李智，崔飞. 几种木质地板材料差热特性分析[J]. 中国安全科学学报, 2012, 22(1): 65-.
[10]	宋文华，杨志舟，李小伟，佴士勇，袁斌. 可发性聚苯乙烯仓库消防安全评价研究[J]. 中国安全科学学报, 2007, 17(7): 139-.
[11]	张小良，沈恒根. 复合无机防火涂料优配研究[J]. 中国安全科学学报, 2007, 17(11): 107-.