落煤过程中涡旋吹吸式除尘技术数值模拟及试验

doi:10.16265/j.cnki.issn 1003-3033.2021.06.016

中国安全科学学报 ›› 2021, Vol. 31 ›› Issue (6): 121-127.doi: 10.16265/j.cnki.issn 1003-3033.2021.06.016

落煤过程中涡旋吹吸式除尘技术数值模拟及试验

荆德吉^1,2 副教授, 贾鑫^1,2, 张天^1,2, 孟祥曦^1,2, 马明星^1,2, 王志恒^1,2

1 辽宁工程技术大学安全科学与工程学院,辽宁阜新 123000;
2 矿山热动力灾害与防治教育部重点实验室(辽宁工程技术大学),辽宁阜新 123000

收稿日期:2021-03-10 修回日期:2021-05-15 出版日期:2021-06-28 发布日期:2021-12-28
作者简介:荆德吉 (1984—),男,辽宁抚顺人,博士,副教授,博士生导师,主要从事粉尘综合治理技术研究。E-mail:jingdeji@sina.com。贾鑫 (1996—),男,河北邯郸人,硕士研究生,研究方向为职业安全与健康。E-mail:593095193@qq.com。
基金资助:
国家自然科学基金青年基金资助(51704146);辽宁省自然科学基金资助(2020-MS-304)。

Numerical simulation and experimental study on vortex blowing and suction dedusting technology during coal falling

JING Deji^1,2, JIA Xin^1,2, ZHANG Tian^1,2, MENG Xiangxi^1,2, MA Mingxing^1,2, WANG Zhiheng^1,2

1 College of Safety Science and Engineering, Liaoning Technical University, Fuxin Liaoning123000,China;
2 Key Laboratory of Mine Thermodynamic Disasters and Control of Ministry of Education (Liaoning Technical University), Fuxin Liaoning 123000, China

Received:2021-03-10 Revised:2021-05-15 Online:2021-06-28 Published:2021-12-28

摘要/Abstract

摘要： 为治理落煤过程中产生的粉尘问题,基于涡旋气流的生成机制及粉尘粒子在涡旋气流场中的运移特性,提出一种控制落煤过程中粉尘扩散的涡旋吹吸式除尘技术;以落煤塔落煤过程为例,利用数值模拟方法分析涡旋吹吸式除尘气流场的变化特征;搭建仿真试验模型,通过仿真试验研究设备最佳涡旋性能参数,对比分析涡旋吹吸式除尘与单一抽吸除尘的除尘性能。结果表明:落煤过程中形成涡旋气流,大部分粉尘粒子被涡旋集聚,呈螺旋状自下而上运动。最佳吹吸比为4.814时,涡旋气流性能最佳;涡旋吹吸除尘性能高于单一抽吸,单位时间集尘质量浓度分别为314.27、191.94 mg/m³,除尘效率分别为93.25%和41.19%,粉尘逃散率分别为6.31%和46.60%。

关键词: 落煤过程, 涡旋吹吸式除尘, 落煤塔, 数值模拟, 除尘技术

Abstract: In order to control dust in the process of coal falling, based on generation mechanism of vortex and migration feature of dust particles in vortex airflow field, a vortex blowing-suction dust removal technology was put forward to control dust dispersion during coal falling. Then, with a coal falling tower as an example, numerical simulation was used to analyze variance law of airflow field. Finally, a simulation experiment model was built, optimal vortex performance of devices was studied, and dust removal performance of proposed technology was compared with that of single suction one. The results show that vortex airflow is formed during coal falling process, and most of dust particles are collected by vortex, migrating bottom-up in a spiral pattern. Vortex performance will be the best at an optimal blowing ratio of 4.814. And dust removal performance of vortex blowing-suction dedusting technology is better than that of single one, with dust collection concentration per unit time being 314.27 and 191.94mg/m³, dust removal efficiency of 93.25% and 41.19%, and escape rate of 6.31% and 46.60% respectively.

Key words: coal falling process, vortex blowing and suction dedusting, coal-falling tower, numerical simulation, dust removal technology

中图分类号:

X964

荆德吉, 贾鑫, 张天, 孟祥曦, 马明星, 王志恒. 落煤过程中涡旋吹吸式除尘技术数值模拟及试验[J]. 中国安全科学学报, 2021, 31(6): 121-127.

JING Deji, JIA Xin, ZHANG Tian, MENG Xiangxi, MA Mingxing, WANG Zhiheng. Numerical simulation and experimental study on vortex blowing and suction dedusting technology during coal falling[J]. China Safety Science Journal, 2021, 31(6): 121-127.

参考文献

[1] 陈景序, 荆德吉, 葛少成. 气动涡旋雾幕性能影响因素试验及优化研究[J].中国安全科学学报, 2019, 29(7): 123-128.
CHEN Jingxu, JING Deji, GE Shaocheng. Experimental study on factors influencing performance of pneumatic vortex spray curtain and its optimization [J]. China Safety Science Journal,2019,29(7): 123-128.
[2] 葛少成, 孙丽英, 荆德吉,等.水雾荷电脱除PM_2.5影响因素试验研究[J].中国安全科学学报,2019,29(3): 139-144.
GE Shaocheng, SUN Liying, JING Deji, et al. Experimental study on influencing factors of water mist charge removal of PM_2.5 [J]. China Safety Science Journal, 2019, 29(3): 139-144.
[3] 袁亮. 煤矿粉尘防控与职业安全健康科学构想[J].煤炭学报, 2020, 45(1): 1-7.
YUAN Liang. Scientific conception of coal mine dust control and occupational safety [J]. Journal of China Coal Society,2020,45(1): 1-7.
[4] 程卫民, 周刚, 陈连军,等. 我国煤矿粉尘防治理论与技术20年研究进展及展望[J].煤炭科学技术, 2020, 48(2): 1-20.
CHENG Weimin, ZHOU Gang, CHEN Lianjun, et al. Research progress and prospect of dust control theory and technology in China' s coal mines in the past 20 years [J].Coal Science and Technology, 2020, 48(2): 1-20.
[5] 陈芳. 综放工作面产尘分布规律及综合治理技术[J].煤炭工程, 2020, 52(3): 76-81.
CHEN Fang. Dust distribution law and comprehensive dust control in fully mechanized top coal caving face [J]. Coal Engineering, 2020, 52(3): 76-81.
[6] 黄宜生,胡胜勇,邵和,等.综掘工作面分级除尘系统及其应用[J].中国安全科学学报,2019,29(9): 150-154.
HUANG Yisheng, HU Shengyong, SHAO He, et al.Research and application of grading dust suppression system on comprehensive heading faces [J]. China Safety Science Journal, 2019,29 (9): 150-154.
[7] 邹常富, 张富兴. 皮带转载点产尘治理技术研究及应用[J].现代矿业, 2019, 35(6):219-221,224.
ZOU Changfu, ZHANG Fuxing. Study and Application of the dust treatment technique in belt transfer point [J].Modern Mining, 2019, 35(6):219-221,224.
[8] MA Qingxin, NIE Wen, YANG Shibo, et al. Effect of spraying on coal dust diffusion in a coal mine based on a numerical simulation[J].Environmental Pollution,2020,264:DOI:10.1016/j.envpol.2020.114717.
[9] WANG Hetang, WU Jinlong, DU Yunhe, et al. Investigation on the atomization characteristics of a solid cone spray for dust reduction at low and medium pressures[J].Advanced Powder Technology, 2019, 30(5): 903-910.
[10] 林爱晖, 李永存. 利用人造龙卷风控制有害物扩散的研究[J].中国安全科学学报, 2014, 24(1): 126-130.
LIN Aihui, LI Yongcun. Investigation on controlling diffusion of noxious substance using artificial tornado [J]. China Safety Science Journal, 2014, 24(1): 126-130.
[11] ARAVIND G P, DEEPU M. Numerical studies on convective mass transfer augmentation in high speed flows with lateral sweep vortex generator and dimple cavity[J]. International Journal of Thermal Sciences, 2020, 153: DOI:10.1016/j.ijthermalsci.2020.106379.
[12] MENNI Y, CHAMKHA A J, AZZI A, et al. Numerical analysis of fluid flow and heat transfer characteristics of a new ind of vortex generators by comparison with those of traditional vortex generators[J].International Journal of Fluid Mechanics Research,2020,47(1): 23-42.
[13] 丛晓春, 张光玉, 詹水芬.露天煤尘污染扩散运动的数值计算[J].煤炭学报, 2007, 32(11): 1 138-1 141.
CONG Xiaochun, ZHANG Guangyu, ZHAN Shuifen. Numerical calculation of mine powder diffusion movement [J]. Journal of China Coal Society, 2007,32(11): 1 138-1 141.
[14] 荆德吉, 徐放, 葛少成,等. 多层螺旋雾幕技术的喷雾模拟及降尘试验研究[J].中国安全生产科学技术,2019,15(8): 70-76.
JING Deji, XU Fang,GE Shaocheng, et al. Study on spray simulation and dust removal experiments of multi-layer spiral fog curtain technology [J].Journal of Safety Science and Technology, 2019, 15(8): 70-76.
[15] 关文玲, 王晓娟, 董呈杰,等. 无上部抽吸装置储罐区人工龙卷风风场模拟[J].安全与环境学报, 2020, 20(1): 98-105.
GUAN Wenling, WANG Xiaojuan, DONG Chengjie, et al. Numerical simulation for the artificial tornado field in a storage tank area with no suction device [J]. Journal of Safety and Environment, 2020, 20(1): 98-105.
[16] 杨胜来.综采工作面粉尘运移和粉尘浓度三维分布的数值模拟研究[J].中国安全科学学报,2001,11(4): 64-67.
YANG Shenglai. Numerical simulation of 3-Dimensional sust sistribution on long wall coal faces [J]. China Safety Science Journal, 2001,11 (4): 64-67.
[17] 王宝晴,张超,刘建.不同风速下巷道断面微细粉尘分布模拟试验研究[J].中国安全科学学报,2018,28(3): 44-49.
WANG Baoqing, ZHANG Chao, LIU Jian. Simulation experimental study on fine dust distribution over roadway section under different wind speeds [J]. China Safety Science Journal, 2018,28 (3): 44-49.
[18] 张小良,叶圣军,刘晓晨,等.水平管道弱激波扬起沉积粉尘运动特征研究[J].中国安全科学学报,2019,29(1): 55-61.
ZHANG Xiaoliang, YE Shengjun, LIU Xiaochen, et al. Study on movement characteristics of dust raised by weak shock wave in horizontal pipeline [J]. China Safety Science Journal, 2019,29 (1): 55-61.

落煤过程中涡旋吹吸式除尘技术数值模拟及试验

Numerical simulation and experimental study on vortex blowing and suction dedusting technology during coal falling

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	李刚, 刘海振, 杨庆贺, 牛伟锋. 带压开采煤层底板破坏特征与突水风险分析[J]. 中国安全科学学报, 2022, 32(5): 68-76.
[2]	郑艾辰, 向晋扬, 黄锋, 金成昊, 刘星辰. 空洞对隧道结构安全影响试验与模拟[J]. 中国安全科学学报, 2022, 32(5): 119-126.
[3]	游波, 毛聪, 施式亮, 刘何清, 鲁义, 李敏. 矿用通风服微空间环境变化特征研究[J]. 中国安全科学学报, 2022, 32(5): 185-193.
[4]	冯巩, 夏元友, 王智德, 严敏嘉. 基于位移信息融合的露天矿边坡动态预警方法[J]. 中国安全科学学报, 2022, 32(3): 116-122.
[5]	鲁义, 杨帆, 刘欢, 陈健, 王金鹏, 李文辉. 气凝胶消防救援服内衬的热阻计算^*[J]. 中国安全科学学报, 2022, 32(1): 201-207.
[6]	张钧祥, 刘彦伟, 任培良, 韩红凯, 左伟芹. 基于蠕变效应的穿层钻孔封孔参数优化与试验研究[J]. 中国安全科学学报, 2021, 31(7): 97-104.
[7]	丁厚成, 连志虚, 邓权龙, 蒋仲安, 杨利炜, 葛梦圆. 振弦栅与高压喷雾协同作用下除尘特性研究^*[J]. 中国安全科学学报, 2021, 31(6): 106-112.
[8]	朱豪豪, 郭海林, ZHUMAKELDI A. 外力作用下管道内表面缺陷处裂纹扩展研究[J]. 中国安全科学学报, 2021, 31(3): 66-72.
[9]	姜学鹏, 陈欣格, 郭昆. 侧部点式排烟隧道火灾临界风速研究[J]. 中国安全科学学报, 2021, 31(3): 105-111.
[10]	王亮, 孙毅民, 褚鹏, 赵伟, 邹双英. 基于时空分布特征的煤层瓦斯测压准确性研究[J]. 中国安全科学学报, 2021, 31(2): 40-47.
[11]	张萌, 刘宏磊, 乔文光, 高勋. 排土场稳定性影响因素显著性研究[J]. 中国安全科学学报, 2021, 31(2): 69-75.
[12]	曲国娜, 李红健, 贾廷贵, 强倩, 王来贵. 煤堆自燃特征的试验研究与数值模拟^*[J]. 中国安全科学学报, 2021, 31(12): 69-77.
[13]	荆德吉, 魏德宁, 马明星, 张天, 孟祥曦, 任帅帅. 胶带运输巷粉尘运移及气动喷雾降尘技术^*[J]. 中国安全科学学报, 2021, 31(11): 93-99.
[14]	崔村燕, 柳宁远, 段永胜, 同江. 长贮库房内偏二甲肼扩散浓度快速估算方法[J]. 中国安全科学学报, 2021, 31(1): 109-115.
[15]	李昂, 司俊鸿, 李雪冰. 泄爆门泄爆特性试验及数值模拟研究[J]. 中国安全科学学报, 2020, 30(8): 51-56.